Tribological behaviour of copper oxide nanoparticle suspension

This work presents and discusses the tribological behaviour of nanoparticle suspensions in a polyalphaolefin (PAO6). CuO nanoparticles were separately dispersed at 0.5, 1.0 and 2.0% wt. in PAO6 using an ultrasonic probe for 2 minutes. AW properties were obtained using a TE53SLIM tribometer with a block-on-ring configuration and EP properties were obtained using a Four-Ball machine according to ASTM D2783. Wear surfaces were analyzed by SEM and EDS after tests. The study led to the following conclusions: nanoparticle suspensions exhibited reductions in friction and wear compared to the base oil; CuO suspensions showed the highest friction coefficient and lowest wear per nanoparticle content of 2%; all concentrations of nanoparticles improved the EP properties of PAO6; CuO showed better results at 0.5% wt. of nanoparticles; and the antiwear mechanism of nanoparticulate additive was produced by tribo-sintering

Tribological behaviour of polyalphaolefins: wear and rolling contact fatigue tests

Polyalphaolefin fluids are gaining rapid acceptance as high-performance lubricants and functional fluids because they have certain inherent, and highly desirable, characteristics relative to mineral oils. One of these characteristics is their low toxicity. It combined with excellent viscometrics and lubricity, have made low-viscosity PAO fluids an important component in lubricant formulations. Typical data found in product specifications for lubricants are the kinematic viscosity and the viscosity index. These values do not give enough information to choose the optimum lubricant for a lubricated contact. In mechanical systems take place rolling, sliding and rolling/sliding contacts, therefore lubricants have to work the best possible in these operation conditions. In this study are experimentally determined the L50, L10 and Weibull´s slope () of polyalphaolefins with two different viscosities. This test was made on a four-ball machine (Stanhope Seta). Wear test also was made on a four-ball tester (Roxana) in order to measure the wear scar diameter (WSD), and the flash temperature parameter (FTP). Lubricants were identified through infrared spectroscopy, and ball´s pittings were observed with SEM

Wear prevention characteristics of binary oil mixtures

This work presents the results of wear prevention tests carried out with mixtures of a polyalphaolefin (PAO 6) and two esters (TMP-05 and Sunflower oil, SO), on a four-ball machine tester. Results show that esters are excellent wear reducers when they are mixed with a low viscosity polyalphaolefin. The optimum ester percentages in PAO 6 were 5% and 15% for TMP-05 and SO, respectively. Better results than in pure PAO 6 occurred in all mixtures. The addition of esters (less than 15%) to PAO 6 hardly changed volume viscosity

Viscosity and tribology of copper oxide nanofluids

Nanofluids, a term proposed by Choi in 1995 [1], are composites consisting of solid nanoparticles with sizes varying generally from 1 to 100 nm dispersed in a liquid. Numerous nanoparticles used as oil additives have been investigated in recent years [2-7]. Results show that they deposit on the rubbing surface and improve the tribological properties of the base oil, displaying good friction and wear reduction characteristics even at concentrations below 2%wt. Although the viscosity of the nanofluids is a property of crucial importance for film forming, and hence friction and wear reduction, which are characteristic of lubricants, only Hwang et al. [8] have studied thermal characteristics, kinematic viscosity and tribological properties of nanofluids simultaneously. In this paper, we present measurements of dynamic viscosity of nanofluids formed by copper oxide nanoparticles dispersed in a polyalphaolefin, for temperatures and concentrations varying from 20 to 60ºC and 0.5 to 2% wt., respectively. Dependence of the nanofluid viscosity to the solid fraction and temperature was compared with existing models and its influence on lubrication was also analysed

Cryogenic MMIC low noise amplifiers

Monolithic (MMIC) and discrete transistor (MIC) low noise amplifiers are compared on the basis of performance, cost, and reliability. The need for cryogenic LNA’s for future large microwave arrays for radio astronomy is briefly discussed and data is presented on a prototype LNA for the 1 to 10 GHz range along with a very wideband LNA for the 1 to 60 GHz range. A table of MMIC LNA and mixer designs under development for the frequencies up to 210 GHz is reported and data on cryogenic amplifiers in the 85 to 115 GHz is reviewed. The current status of the topics of transconductance fluctuations and cryogenic noise modeling will be briefly summarized

Some aspects of oil lubricant additivation with ZnO nanoparticles

This is a study on the tribological behaviour of ZnO nanoparticles as an additive in a polyalphaolefin (PAO6) and on the influence of dispersing agents (OL100 and OL300). Antiwear and extreme pressure tests were run on two four-ball machines. Firstly, it was demonstrated that OL300 has better dispersant properties than OL100, and also was found formation of aggregates for 1 and 1.5% of ZnO in PAO6 + 3% OL300 suspension. Ensuing SEM and EDS analysis of the worn surface highlighted a number of conclusions: OL100 and OL300 are potentially useful as wear reducer additives in PAO6, the non-coated ZnO nanoparticles had an abrasive behaviour, and ZnO nanoparticles do not act as anti-wear agent under certain conditions but in EP conditions they can decrease wear

Investigating Unused Tools for the Animal Behavioral Diversity Toolkit

Behavioral diversity is a commonly used tool used to quantify the richness and evenness of animal behaviors and assess the effect of variables that may impact an animal’s quality of life. The indices used in behavioral diversity research, and the study subjects, have not been formally reviewed. This paper aims to identify which indices are being used in behavioral diversity research, and under which scenarios, and uncover novel indices from other disciplines that could be applied to behavioral diversity. To investigate the techniques and species investigated in behavioral diversity literature, a Web of Science literature search was conducted. Two methods: behavioral richness and the Shannon–Wiener index, were the most frequently used indices, whereas the Behavioral Variability index featured rarely. While a range of species appeared in the behavioral literature, mammals were the most frequently studied Class, whereas amphibians did not feature in any papers. There are several diversity indices which did not feature in behavioral diversity including Simpson’s index, and Chao. Such indices could be used to better understand animal behavioral study outputs or be used to estimate the number of ‘unobserved’ behaviors that an animal may express. Future studies could therefore extend beyond the Shannon–Wiener and richness indices.James Edward Brereton, and Eduardo J. Fernande

Horner's Syndrome due to a Spontaneous Internal Carotid Artery Dissection after Deep Sea Scuba Diving

Internal carotid artery dissection (ICAD) is a rare entity that either results from traumatic injury or can be spontaneously preceded or not by a minor trauma such as sporting activities. It represents a major cause of stroke in young patients. The diagnosis should be suspected with the combination of Horner''s syndrome, headache or neck pain, and retinal or cerebral ischaemia. The confirmation is frequently made with a magnetic resonance angiography (MRA). Although anticoagulation with heparin followed by vitamin-K-antagonists is the most common treatment, there is no difference in efficacy of antiplatelet and anticoagulant drugs at preventing stroke and death in patients with symptomatic carotid dissection. We describe a patient with ICAD following deep sea scuba diving, who presented with Horner''s syndrome and neck pain and was successfully treated with anticoagulants

Extreme pressure behaviour of newly formulated oil-in-water emulsions

Oil-in-water (O/W) emulsions are broadly used in metal-machining processes, where combined lubrication and refrigeration are needed, such as in cutting, rolling, or grinding. These fluids consist of tiny oil droplets in water stabilised by small amounts of emulsifiers, namely surfactants. In an emulsion, oil is responsible for the lubricating properties, whereas water provides heat dissipation and fire resistance. Normally, emulsifiable metalworking oils are used in an oil concentration between 2 and 5 vol. %, depending on the application. Despite their wide use, the lubrication mechanisms of o/w emulsions have not been fully understood, mainly because of their complexity. Previous studies on oil-in-water emulsions showed that, in order to form thick lubricant films, oil droplets must wet the metal surfaces, displacing water. The ability of oil to wet is strongly dependent on the concentration of surfactant. Surfactant molecules tend to adsorb preferentially at the interface, modifying the nature of the layers adjacent to the metal surfaces and, thus, playing a key role in processes such as wettability, corrosion, or friction, as well as emulsion stability. The aim of this work is to study the influence of concentration of two different emulsifiers (anionic and non-inonic) on the wettability and extreme pressure properties of an oil-in-water emulsion. A mixture of a synthetic polyalphaolefin and a trimethylol propane ester was used as the base oil, and the concentrations of emulsifiers were below, equal to, and above their critical micellar concentrations (CMC). Extreme pressure tests (ASTM D 2783), which try to simulate the operating conditions of high speeds and pressures taking place in cutting processes, and contact angle measurements were carried out in order to establish a relationship between both properties and to evaluate the performance of these emulsions as lubricants